Backsplash Idea: Faux Stone Re-Finish

By Joe Provey

Faux Stone Backsplash

The faux-finished backsplash tiles. Photo: JProvey

My wife, Mary Ann, hated the backsplash tiles in our kitchen, and I agreed they were slightly dated. Unfortunately, the crackled glass that we wanted to replace them with was amazingly expensive: $17 per square foot (more than $500 for the 30 sq. ft. that we would need). So I did what any good husband would do—I stalled.

Related: 11 Backsplashes for a Unique Kitchen

But one day, while she was at work, I decided to do a little experiment. I applied a mixture of primer, glaze and artist’s oils to some spare tiles to see if I could create a faux stone finish that would give the existing tiles a fresh new look—at little to no cost. And it worked!

Here’s a step-by-step of how I created the look:

Step 1: Run a palm sander with a fine, 220-grit disk over the backsplash to roughen up the existing tiles. Clean the surface with a TSP substitute.

Step 2: Using a 6-inch foam roller, apply three coats of pigment shellac-based primer (I can recommend B-I-N by Zinsser); allow at least 45 minutes dry time between coats.

Step 3: To create the faux, mottled coloration you will need to purchase tubes of artist’s oil paints. I used Payne’s Grey (a bluish grey), Raw Umber, and Zinc White (about $6-$7 per tube) to get my Tuscan stone look. You will also need to purchase a clear alkyd glaze, similar to what you would use to create a faux wall finish (Benjamin Moore’s #409 00 is a good choice at $14 per quart.)

Faux Stone Backsplash - Glaze

Applying first color-glaze coat on primed tiles. Photo: JProvey

Step 4: In a disposable aluminum tray, mix a quarter-size dollop of the grey oil paint with a half-cup of glaze and test it on a part of the backsplash hidden from view (like behind the range). When you find a mixture that gives you about a 30 percent tint, wipe a coat over the entire backsplash using a cotton rag. Don’t worry about whether some gets on the grout; the joints will be colored.

Faux Stone Backsplash - Stipple

Photo: Joe Provey

Step 5. While the first coat is drying, mix the Raw Umber and glaze in the same ratio as above. Beginning where you started the first coat, apply the umber-glaze mixture with a balled-up rag. Use a stamping motion to allow about 25 percent of the first coat to show through. The folds in the rag will produce the random, mottled look of marble. If you don’t like the way your first attempts look, wipe it off with a rag dampened in turpentine and try again.

Step 6: You can create a stippled look by mixing the grey oil paint and glaze in a 50-50 ratio and apply with an old toothbrush. A fine, thin brush with long bristles will be best for veining.

Faux Stone Backsplash - Complete

The faux effect you want to imitate. Photo: JProvey

Step 7:  The last step is to paint the grout. The product I used—Polyblend’s Grout Renew—is both a colorant and sealer. If you can’t find a premixed color that you like, buy the white and tint it yourself. Use artist’s acrylic paint, not oils, with water-based grout sealer.

The total cost of the project came to about $60, with half of that being a quart of shellac-based primer. Even better, it was done in 5 hours and in time for dinner!


You work hard for your money. We work just as hard to give you the best value for your money. Value, service, honesty: that’s the Air Temp promise. Remember Heating and air maintenance is the best defense against excess spending, and replacement. We are located in Greer SC, but that does not mean we will not service those outside Greer. So even if your outside the upstate of SC, contact us and we can work something out just for you.

Heating and Cooling Repair in Greer SC

Sometimes the most cost effective course of action is to replace an old, inefficient furnace or air conditioner with a new high-efficiency unit. New units save you money on your monthly heating and cooling bill: sometimes a lot of money. Now with tax breaks and other incentives you can save now and later.